Skip to content
Premium

Designing the Ideal Dive Deck for Raja Ampat Day Boats

A dive deck is judged by one number: how many minutes it takes to turn a boat around between dives.

Designing the Ideal Dive Deck for Raja Ampat Day Boats
Boat builders framing small wooden hulls suited to homestay and day-trip work
01

A dive deck is judged by one number: how many minutes it takes to turn a boat around between dives. Everything else — comfort, safety, guest satisfaction — follows from a layout that moves divers and cylinders in one direction without crossing paths. This is how we lay out a Raja Ampat day boat, and which materials survive the conditions.

Shipwright fitting and fastening a plank on a new-build hull
02

The principle: one-way flow, one cylinder handling

Draw the diver’s journey before drawing the deck. Guests board, stow dry bags, sit, kit up at their own station, step to the entry point, dive, return via the ladder, de-kit, rinse, and move to shade. If any of those steps requires walking back through the previous one, the deck is wrong.

The same applies to cylinders. A well-designed boat has crew handling each tank once: it sits in the rack where the diver kits up, and the change between dives happens at that station. Boats where tanks are stored forward and used aft generate constant traffic in the narrowest part of the vessel, exactly where people in fins are trying to move.

Boat builders planking a wooden hull with bamboo shoring at the yard
03

Tank racks and kit stations

  • Individual stations. Each diver gets a numbered seat, a tank position and a hook or cubby for mask, computer and gloves. This alone eliminates most of the chaos on a busy boat.
  • Rack height. Cylinders should be liftable into position without a full squat and without lifting above shoulder height. Both extremes cause crew back injuries over a season.
  • Positive retention. Bungee alone is not enough in a Dampier Strait chop. Use a physical restraint that holds the cylinder even when the boat rolls hard.
  • Drainage under the racks. Standing salt water rots timber and corrodes fittings faster than anything else on a dive boat.
Boat builder working under a shelter at a coastal yard in Indonesia
04

Entry and exit

Boarding is where most day-boat designs fail. The ladder must be wide enough for a diver in fins, immersed deep enough that the first rung is reachable from the water in a swell, and angled rather than vertical. A second ladder is worth the cost on any boat carrying more than twelve divers, because it halves the time in the water at the end of a drift dive — which in a running current is a safety improvement, not just convenience.

The entry point needs a clear, non-slip step and enough deck ahead of it for a diver to do a final check without blocking the queue. Where drift diving is routine, a tender or chase capability changes the whole safety picture. See dive boat new-builds.

Yard crew with layout tools used to mark out hulls for survey and support craft
05

Rinse and camera areas

Separate the rinse tanks. One for masks, computers and small kit; a second, larger and cleaner, exclusively for camera housings. Mixing them is how expensive housings get flooded by someone else’s fin strap catching a latch.

Raja Ampat attracts underwater photographers, so the camera table has stopped being optional. What it needs: a padded, drained surface at working height; individual power outlets, generously specified; secure stowage that holds housings through a rough crossing; shade over the table; and enough space that two people can work without touching each other’s gear.

Large wooden hull under construction at a coastal Indonesian boatyard
06

Shade, seating and dry stowage

Divers spend far more time sitting on a boat than diving from it. Shade must cover seated guests at the sun angles you actually operate in, including early morning and mid-afternoon, not just at noon. Bench seating with backrests beats moulded seats for a mixed group in wetsuits, and cushions must drain rather than absorb.

Dry stowage needs to be genuinely dry — sealed lockers, not an area under a tarpaulin. Guests carrying passports, phones and camera bodies notice immediately, and it is one of the lowest-cost quality signals a boat can send.

Two wooden hulls standing side by side on the slip during construction
07

Decking materials that survive

Material Performance Watch point
Dense tropical hardwood Excellent grip wet, cooler underfoot than synthetics, refinishable locally Needs periodic maintenance and good drainage; sourcing should be legal and documented
Synthetic foam decking Very low maintenance, good grip, comfortable Retains heat in direct sun; adhesive quality determines lifespan in tropical UV
Non-skid painted GRP Lowest cost, easily repaired, light Wears in traffic lanes; gets hot; needs periodic recoating
Marine plywood with non-skid Low cost, locally repairable Shortest life; unforgiving of standing water and poor sealing

Whichever is chosen, three details determine how long it lasts: drainage that actually clears the deck, sealed fastener penetrations, and a freshwater rinse routine after every trip. Material context is in wood vs aluminium vs fiberglass and hull material options.

Boatyard crew carrying long planks into position during hull construction
08

Common mistakes

  1. Tank racks placed where divers must carry cylinders past seated guests.
  2. A single ladder on a boat running drift dives with sixteen divers.
  3. Shade sized for the anchored photograph, not for a boat underway at 08:00.
  4. Camera rinse shared with general rinse.
  5. No drainage under racks and benches, guaranteeing rot and corrosion.

To lay out a deck around your actual dive schedule, contact +62 811 3941 4563 or bd@juaraholding.com.

Builder working on the bow of a vessel afloat during commissioning and fit-out
09

Frequently Asked Questions

What decking materials last longest on tropical Raja Ampat dive boats?

Dense tropical hardwood offers excellent wet grip, stays cooler underfoot than synthetics and can be refinished locally. Synthetic foam decking needs almost no maintenance but retains heat. Non-skid painted GRP is least expensive and easily repaired but wears in traffic lanes. Drainage, sealed fastener penetrations and a freshwater rinse routine matter more than the material itself.

How should tank racks be positioned on a dive day boat?

At each diver’s own seating station, so a cylinder is handled once rather than carried across the deck. Rack height should allow lifting without a full squat or reaching above shoulder height, retention must be positive rather than bungee alone, and drainage under the racks is essential.

How many boarding ladders does a dive boat need?

One is workable up to about twelve divers. Above that a second ladder is worth the cost because it halves the time divers spend in the water at the end of a drift dive, which in a running current is a safety improvement rather than a convenience.

Why separate the camera rinse tank?

Because mixing camera housings with masks, fins and computers is how housings get flooded — a strap or buckle catches a latch. A dedicated, larger and cleaner tank for housings only is standard on any Raja Ampat boat carrying photographers.

, , ,

Indonesian boatyard building new wooden boats at sunset for Raja Ampat operators
Next Step

Ready to get started?